Move bobbin winder switch to the left, remove bobbin and retighten stop motion screw.If bobbin does not wind evenly, loosen screw G which holds tensio
1. Raise needle to its highest position.REPLACING BOBBIN CASE2. Hold bobbin case by latch and place it on the stud of the shuttle allow
RAISING THE BOBBIN THREADNow that you have wound the bobbin and threaded the needle, you will need to raise the bobbin thread through
3.straight StitchingpreparationBefore moving the stitch width selector, make sure the needle is above the needle plate.SETTING THE MACHINE1. Pr
IStarting to Sewstarting to seiv1. Position the needle in the fabric where desired for stitching start.2. Lower the presser foot and start the mach
adjusting selectors for your fabricSETTING STITCH LENGTHThe stitch length selector regulates the length of both straight and zig zag stitc
Regulating PressureThe pressure screw regulates the pressure that the presser foot exerts on the fabric. Correct pressure is important
Correct tension is important because too much or too little will weaken your seams or cause the fabric to pucker. Make a test sam
Bobbin-Thread TensionTo IncreaseBobbin-Thread TensionBobbin thread tension is controlled by a screw located on the bobbin case. You will
sew mg a seamPIN BASTINGPin basting IS a time-saver and can be used in place of hand basting when you are straight stitching seams in
£ njoy Carefree Sewing!Congratulations-You are about to discover the wonderful pleas- uie of sewing with your new SINGER sewing machine.
Keeping Seams StraightStitching Line ----34 SIIV inch SeamKEEPING SEAMS STRAIGHTTo keep the seam straight, use one of the numbered guidelin
REINFORCING END OF SEAM1. Stitch to the edge of the fabric.2. Raise stitch length selector as far as it will go and backstitch to reinfo
4.Zig-Zag StitchingYou will find the zig zag stitch that is built into your machine ideal for many of your sewing applications. To
Needle position setting of centre places stitching in central needle position. Settings left and right place stitching in left or ri
adjusting needle-thread tensionZig zag stitching requires less needle thread tension than straight stitching: and closed zig zag stitchin
For open zig-zag stitching, choose any stitch length from 6 to 20, depending on how open you wish the stitching to be. It you wi
5. Sewing the Professional WaySeams in Knit Fabricsconstruction detailsSEAMS IN KNIT FABRICS• Needle Position: Centre• Stitch Width: 1 to 2• Stitc
LINGERIE SEAMS• Needle Position: Centre• Stitch Width: 2 to 3.• Stitch Length: 1 5 to 20, depending on fabricTo make seams in lingerie both d
FLAT-FELLED SEAMSFlat-Felled Seams• Needle Position: Centre• Stitch Width: 2 or 3• Stitch Length: 1 5 to 20, depending on fabricZig-Zag stitching g
SEAM FINISHES• Needle Position: Centre• Stitch Width: 4 or 5• Stitch Length: 8 to 20, depending on fabricSeam edges support the garment and shouldb
CONTENTSPage1. Getting to Know Your Machine... 2Principal Parts and What They Do... 2.32. Getting Ready to Sew...
DARTSRegular DartSteps in Making a Dart in Interfacing“Hi"""”“— 28-Darts can be made in the usual way on your sewing machine.
BUTTONHOLES• Needle Position: Left• Stitch Width; 3 and 5• Stitch Length: Above 20• Special-Purpose FootMake a test buttonhole on a sample
Buttonholes (Continued)Side StitchingA c BProcedurePlace work under the presser foot, aligning centre marking of buttonhole with the needleSide
Side stitchingReset stitch width selector to 3 and stitch, stopping at point EButtonholes (Continued)Side StitchingFinal bar tackWith needle
BUTTON SEWING• Needle Position: Left• Stitch Width: See illustrations• Feed Throw-out Knob: To Right (Darning) PositionFlat buttons, one inch o
keeping up appearancesMENDINGThe zig zag stitch is just as useful for mending as it is for creative sewing. It forms a firm, flexibl
Replacing ElasticReplacing ElasticWhen replacing elastic, use the same settingsas (or "Mending a Tear "1. Fit elastic for desired snugn
BLANKET BINDINGOften you can make an old blanket look almost new by replacing the binding.• Needle Position: Centre• Stitch Width: 5• Stitc
DarningDARNINGWorn or torn spots on children's clothes and household linens can be darned effortlessly and quickly with little practi
With Embroidery Hoop• Needle Position: Centre• Stitch Width:0• Stitch Length: In FINE Area (Above 20)• Feed Throw-out Knob: To Right (Darning)Posi
1 .Getting to Know Your Machineprincipal parts and what they do1. Pressure Regulating Thumb Screw regu lates presser foot pressure on the fabric.2.
decorative satin stitchingMethod 'Trimming after StitchingMethod 2-St<tching after TrimmingAPPLIQUEApplique adds beauty and interest to
6.Caring for Your Machinecleaning and lubricatingYour machine will serve you perfectly tor many years if you keep it clean and lubricate
TO REMOVE AND REPLACE THE SHUTTLEThe shuttle can be removed for cleaning in the follow ing manner.1. Tilt machine back.2. Turn hand wheel until need
IF MACHINE IS TO BE STOREDBefore storing, thoroughly clean the machine to remove all traces of lint and fluff. Then swab all exposed m
Adjusting Motor Belt Tensionadjusting motor belttensionTension on the motor belt should be just sufficient to keep the belt from slippi
performance checklistRemember To...If Fabric Fails to Feed, Make Sure... If Thread Breaks, Make Sure...Plug machine into an electrical outlet.Turn
Your personal measurement chartThis chart will enable you to keep a record of your measurements You will need the assistance of someo
Adjusting Motor Belt Tension... •42Adjusting Selectors...13,20Applique...
Everything you need to sew up fashion is at a nearby Singer Sevi/ing Centre. Fabulous fabrics plus matching thread, zippers, and all the trimmings tha
PRINCIPAL PARTS OF MACHINE 287N17. Stitch Width Selector— 3—
Electrical Connectionspower and Light Switch2.Getting Ready to Sewpreliminary stepsCONNECTING MACHINEBefore plugging in your machine, be sure t
fabric, thread, needle and stitch length tableFABRICSTHREAD SIZEScat 2020(1 5 x1)NEEDLE SIZESSTITCH LENGTH SETTINGDELICATE ^ tulle, chiffon, fine lace
NEEDLES AND THREADThis machine uses needles Catalogue 2020 (15x 1), available in sizes 9. 11, 14. 16 and 18.For perfect stitching, select c
REMOVING THE BOBBIN1. Raise presser foot and turn hand wheel toward you until needle is at its highest point.2. Drawslide plate to the left.
Komentarze do niniejszej Instrukcji